New Tank or Tankless Unit
We supply Rheem, Bradford White, A.O. Smith, Navien, or Rinnai equipment sized to your household. The unit is registered for warranty in your name, and we hand you the paperwork at the end of the visit.
Every install includes the parts and labor to do the job right, not just drop a tank on the pad. Here is what comes standard on a water heater installation Bowie MD job, and what we handle as an add-on when your setup needs it.
We supply Rheem, Bradford White, A.O. Smith, Navien, or Rinnai equipment sized to your household. The unit is registered for warranty in your name, and we hand you the paperwork at the end of the visit.
Flex connectors, a fresh T&P relief valve, a drip leg on gas units, and a new expansion tank where code requires one. We do not reuse old fittings that are near the end of their life.
We confirm the flue size and slope on gas units and check the dedicated circuit and breaker on electric units. If the existing vent or wiring is undersized, we quote the upgrade before we start.
Every joint is pressure-tested with a gauge, the tank is filled and bled, and the burner or element is cycled to confirm it holds temperature. We set the thermostat to 120 degrees and label the shutoffs.
We drain the old tank, disconnect it, and take it with us for recycling. No bulk pickup appointment, no tank sitting in your garage for a month, no extra fee on the invoice.
When Prince George's County requires a plumbing permit for the install, we pull it and schedule the inspection. You get the signed-off paperwork for your records and for resale.
Water heater installation Bowie MD is the licensed removal of your old tank or tankless unit and the code-correct installation of a new one, including the supply lines, venting, T&P valve, expansion tank, and electrical or gas connection. We size the unit to your household, set it on a level pad or bracket, pressure-test every joint, and walk you through the controls before we leave. A standard 40- or 50-gallon tank swap takes two to four hours; a tankless conversion or a gas line upgrade can run a full day.
Most Bowie calls start the same way: a 12-year-old tank is leaking from the bottom, the pilot won't stay lit, or the water never gets hot enough for a family of five. If you need to replace old water heater Bowie Maryland equipment before it floods the basement, we can usually schedule same-day service. We also handle 50 gallon water heater installation Bowie MD for larger households and gas water heater installation Bowie MD where a dedicated flue and gas shutoff are already in place.
No mystery, no surprise charges. Here is the exact sequence we follow on a water heater install in Bowie, from the first phone call to the final walkthrough.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Pipe wrench and tube cutter
Used to break loose old unions and cut copper or PEX tubing cleanly so the new connectors seat without burrs or leaks.
Soldering torch and press tool
For copper pipe joints, we solder where the line is accessible and use a press tool in tight spots where a flame is not safe.
Pressure gauge
We test the new install and the house supply at the same time. A reading over 80 psi means a pressure-reducing valve is due, which protects the new tank.
Leak detection equipment
When a puddle shows up near the heater, we confirm whether the tank, a fitting, or an underground line is the source before we quote a replacement.
Pipe fittings, solder, and Teflon tape
New fittings, lead-free solder, and thread sealant on every threaded connection. We do not reuse old unions or tape on a new install.
Water heater anode rod
We check and replace the anode rod where needed. It is the sacrificial part that keeps the tank from corroding, and it is cheap insurance on a new unit.
Code-correct venting per Maryland State Plumbing License
Gas units get the right flue size, slope, and termination. We confirm the vent meets code before the burner is lit, which matters in older Bowie homes where the original flue was sized for a smaller tank.
Pressure testing every joint
We fill the system and hold pressure with a gauge before we call the job done. Any joint that does not hold gets redone on the spot, not after you notice a puddle a week later.
Thermostat set to 120 degrees
We set the temperature to 120 degrees, which is the safe, efficient setting for most households. If you want it hotter, we show you how to adjust it and explain the scald risk.
Permit and inspection when required
We pull the Prince George's County permit when the job requires one and meet the inspector on site. The signed-off paperwork goes in your file for resale and insurance.
01
What we do: We treat it as a priority call, bring a 50-gallon Rheem on the truck, and install it the same day. We haul the old unit away and have hot water back before the guests land.
→ Hot showers for the holiday, no flooded basement, and a new unit under warranty.
02
What we do: We size the demand by bathroom and fixture count, recommend a 50-gallon unit, and install it with a new expansion tank and T&P valve. We set the temperature to 120 degrees and show them the flush schedule.
→ Back-to-back showers without a cold surprise, and a tank sized for the household.
03
What we do: We check the gas line size and venting route, then install a Navien or Rinnai unit with the right vent kit and a dedicated circuit. We pull the permit and walk through the annual flush.
→ Endless hot water, reclaimed floor space, and a unit that can last 20 years with maintenance.
04
What we do: We replace the heater and repair the corroded section with new copper pipe and fittings while the water is off. One visit, one permit, one invoice.
→ A new heater and a repaired line, with no second service call a month later.
Bowie homes range from 1960s ranches in Old Bowie to newer builds in Woodmore and Enfield Chase, and the water heater setup changes with the decade. Older homes often have a 40-gallon tank in a tight closet with a flue that was sized for the original unit, so we check venting and clearance before we pick a replacement. Newer homes may have a dedicated tankless closet or a garage pad with a pan and drain. Bowie sits in Prince George's County, and WSSC supplies the water, which runs moderately hard and shortens tank life if the anode rod is not checked. Winter cold snaps can freeze exposed lines in garages and crawlspaces, so we insulate the new connectors and check the shutoff while we are there. If you need water heater installation cost Bowie MD 20721 answers, call us and we will quote by phone after a few quick questions.
Old Bowie
Older ranches and capes with tight utility closets. We measure clearance and confirm flue size before recommending a tank, since a taller unit may not fit the existing space.
Belair at Bowie
Mid-century homes where the original 40-gallon tank is often at end of life. Many owners here upgrade to 50 gallons when the family grows, and we check the gas line size for the larger burner.
Woodmore
Newer construction with garage pads and pans. Tankless conversions are common here, and we confirm the gas meter capacity before quoting a Navien or Rinnai unit.
Pointer Ridge
A mix of townhomes and single-family homes. Townhome installs often need a press tool instead of a torch in tight mechanical rooms, and we plan for that on the first visit.
Moderately hard WSSC water
Hard water shortens tank life by scaling the elements and consuming the anode rod faster. We check the rod on every install and recommend a flush schedule that fits Bowie water.
Winter freeze risk in garages and crawlspaces
Exposed lines in unheated spaces can split in a cold snap. We insulate new connectors and confirm the shutoff works so a frozen line does not turn into a burst pipe.
Older homes with undersized flues
A larger tank on the original flue can backdraft. We size the vent to the new unit and upgrade it when needed, which keeps the install code-correct and safe.
Some water heater problems are worth repairing. Others mean the tank is on borrowed time. Here are the situations where a new install is the right call for Bowie homeowners.
Problem
A leaking water heater can dump 40 to 80 gallons on your basement floor in under an hour, ruining drywall, flooring, and stored belongings. Once the tank shell itself is weeping, no repair will stop it.
Our Fix
We shut off the supply, drain the tank, and install a new unit the same day when stock allows. We also check the pan and floor drain so the next failure, years down the road, drains safely.
Problem
A tank full of sediment or a failing lower element means your household runs out of hot water mid-shower. It also drives up gas or electric use because the unit runs longer to heat less water.
Our Fix
We flush the tank and test the elements first. If the unit is over 10 years old or the tank is heavily scaled, we quote a new 50 gallon water heater installation Bowie MD upgrade sized to your bathroom count.
Problem
Rust-colored hot water usually means the anode rod is gone and the tank interior is corroding. Left alone, the tank will fail from the inside out, often within a year.
Our Fix
We inspect the anode rod and the tank interior. If corrosion has started, we replace the unit and add a fresh anode rod so the new tank lasts its full warranty period.
Problem
A gas unit that will not stay lit can be a thermocouple, a draft issue, or a cracked heat exchanger. It is also a safety concern, especially in a closed basement.
Our Fix
We diagnose the gas train and venting with a pressure gauge and combustion check. If the unit is past its service life, we install a new gas water heater with correct venting and a drip leg.
A new water heater is not just about hot showers. It is about lower gas bills, fewer emergency calls, and a unit that meets current Maryland plumbing code. Here is what a proper installation gets you.
Hot Water Back Same Day
Most standard tank replacements are finished in two to four hours, so a morning call often means hot water by dinner. We stock Rheem and A.O. Smith tanks in common sizes on our trucks, which cuts the wait for water heater replacement Bowie MD customers need in a hurry.
Lower Energy Bills
A modern tank with a factory insulation blanket and a smart thermostat uses 15 to 20 percent less energy than a 12-year-old unit. Tankless models from Navien and Rinnai can cut standby losses further, especially in smaller Bowie households with two or fewer bathrooms.
Code-Correct Venting and Safety
We install a new T&P relief valve, expansion tank, and drip leg on every gas job, and we check that the flue meets Maryland State Plumbing License requirements. That matters in older Bowie homes where the original venting was sized for a smaller tank.
Warranty That Actually Transfers
A professional water heater installation Bowie MD job keeps the manufacturer warranty intact. DIY installs often void the tank warranty, and a failed anode rod at year three can mean a full replacement out of pocket. We register the unit and hand you the paperwork.
Typical 2026 pricing in this area runs $1,200 to $2,400 for a standard 40- or 50-gallon tank install, and $3,000 to $5,500 for a tankless conversion. The unit itself is about half the cost; labor, permits, venting, and disposal make up the rest. We quote a flat price before we start, and we do not charge extra for the estimate or the haul-away. If you are comparing professional water heater installation Bowie MD quotes, ask whether the price includes the permit and the old unit removal, because some do not.
Typical Investment Range
$1,200 - $5,500 depending on unit type and scope
A new heater that is sized and installed correctly lasts 10 to 12 years for a tank and up to 20 for tankless. The upfront price includes the permit, the haul-away, and a pressure-tested install, so you are not paying twice for the same job.
What changes the price
Tank vs. tankless
A standard tank is the lower-cost option and fits most Bowie homes. Tankless units cost more up front and often need a gas line upgrade and a new vent, which adds to the install.
Unit capacity
A 40-gallon tank costs less than a 75-gallon unit. We size by bathroom count and peak demand so you are not paying for capacity you will never use.
Gas line and venting
If the existing gas line is undersized or the flue needs a liner, that adds labor and materials. We check both before quoting so the price you get is the price you pay.
Permit and inspection
Prince George's County requires a permit for most replacements. We include it in the quote when it applies, so there is no surprise line item later.
Access and location
A basement pad with a wide door is a straightforward job. A tight closet, attic, or crawlspace takes longer and may need a press tool instead of a torch, which affects labor.
Google ★★★★★4.9
Called about a leaking tank and they had a plumber at my door in under three hours. New 50-gallon Rheem installed, old one hauled away, and the price matched the phone quote. Clean work and no upsell.
Yelp ★★★★★4.8
Tankless conversion in our Woodmore home. They handled the gas line upgrade and the permit, and the inspection passed the first time. Walked us through the annual flush before they left.
BBB A+
Emergency replacement on a Saturday in Old Bowie. The plumber was professional, explained the flue issue clearly, and had hot water back by mid-afternoon. Fair price for a weekend call.
Our team holds Maryland State Plumbing License credentials and WSSC Licensed Plumber registration, and we work to Prince George's County code on every job. We install Rheem, Bradford White, A.O. Smith, Navien, and Rinnai units, and we keep common tank sizes on the truck so most Bowie jobs finish in one visit. Gas work is done by plumbers with gas-fitting experience, and every install is pressure-tested before we call it done. We also carry Backflow Prevention Certification where the job requires it.
Real experiences from customers who chose our Water Heater Installation services.
“Our 14-year-old tank started leaking on a Friday morning. I called at 9 and the plumber was here by 11 with a 50-gallon Rheem on the truck. He had the old one out and the new one running by 2:30. Cleaned up everything and took the old tank with him. Price was exactly what he quoted on the phone.”
Denise M.
Homeowner, Pointer Ridge
“We switched from a tank to a Navien tankless and the crew handled the gas line and venting without any drama. They pulled the permit and the inspection passed first time. Took most of a day but they walked me through the controls and the flush schedule before they left.”
Marcus T.
Homeowner, Belair at Bowie
“I had a gas water heater installation Bowie MD job that two other companies said needed a full replumb. These guys replaced the shutoff valve and the drip leg and installed the new Bradford White for a third of the other quotes. Honest diagnosis and no upsell. I will use them again.”
Karen S.
Homeowner, Tulip Grove
Real answers to the questions we hear most often from local homeowners and property managers.
A leaking water heater at 2 a.m. is an emergency. We shut off the water, stop the damage, and schedule the install for first thing in the morning. Same-day emergency water heater replacement Bowie MD calls are a regular part of our week.
View Emergency PlumbingSediment from an old tank can settle in your lines and slow drains. When we install a new heater, we can also clear the nearby floor drain or run a drain snake so the pan and drain line work the way they should.
View Drain CleaningNot every failing heater needs replacement. If your unit is under eight years old and the issue is a bad element, thermostat, or anode rod, repair may be the smarter call. We diagnose honestly and only recommend a new install when it makes financial sense.
View Water Heater RepairTankless units from Navien and Rinnai free up floor space and deliver endless hot water. We handle the gas line sizing, venting, and electrical work, and we walk you through the maintenance schedule so the unit lasts its full 20-year lifespan.
View Tankless Heater InstallationA puddle near the heater is not always the tank. We use leak detection equipment and a pressure gauge to find the real source, whether it is a failed T&P valve, a corroded copper pipe, or a slab leak under the floor.
View Leak DetectionBowie winters can split a supply line in an unheated garage or crawlspace. We repair the burst pipe, then check the water heater connections while we are there so a small repair does not turn into a flooded basement.
View Burst Pipe RepairCall us at +1 (831) 293-1204 for same-day service or to schedule a visit. We answer the phone 24/7 for emergencies and return messages within one business day for non-urgent requests. Our office is in Bowie, Maryland, and we serve all of Prince George's County.
Phone
+1 (831) 293-1204Address
16704 Melford Blvd #400, Bowie, MD 20715
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available